Hobart dishwasher error codes
What PROFI and ECOMAX error codes mean, safe checks to try first, and when to call a technician.
Error on the display and service starting soon? Call 0800 90 60 30. Calls are answered 24 hours, 7 days. Technician cover runs 7 days, with after-hours emergency cover. Our target for emergency responses is two hours. It's a target, not a guarantee, and it depends on workload at the time.
Hobart PROFI machines and Hobart ECOMAX machines use different error codes. The same number can mean different things. Error 13 on a PROFI is not the same as Er 13 on an ECOMAX. Before you switch off, photograph the display and note the model from the rating plate, then use the section that matches your machine. CES Wellington are Hobart service agents. See all brand pages on error codes.
Hobart PROFI AMX, AMXX and PREMAX AUP (hood-type)
These machines show a three-digit code and a message on the display. Hobart splits them into two groups.
Fault indications. You can keep washing with limits. The ON/OFF button flashes green and red.
| Code | What it means | What you can safely do |
|---|---|---|
| 003, 004, 008, 009 | Temperature not reached. | Call us. Leave the panels on. |
| 018 | Water level regulation in the wash tank. The drain pump runs to correct the level. | Acknowledge the message. If it keeps coming back, call us. |
| 021 | Fault in the drain system. | Press and hold the ON/OFF button for 3 seconds to restart the pump-out. Check the drain hose isn't kinked or blocked. If it comes back, call us. |
| 022 | Fault in the drain system. | Check the drain hose isn't kinked or blocked. If it comes back, call us. |
| 029 | Programme aborted. Close the hood. | Close the hood fully. |
| 034 | Service interval due. | Call us to arrange a service. |
| 036 | Detergent low. | Top up or replace the detergent. |
| 037 | Rinse aid low. | Top up or replace the rinse aid. |
| 038 | Input voltage too high. The machine has switched off. | Have the power supply checked by an electrician. Call us. |
| 039 | Filling programme aborted. Close the hood. | Close the hood fully. |
| 040 | Run the hygiene programme. | Run the machine's hygiene programme as the operating manual describes. |
| 041 | External water treatment cartridge used up. | The water treatment cartridge needs replacing. Call us if you're not sure how. |
| 043 | Salt low (machines with built-in water treatment). | Refill the regenerating salt as the manufacturer directs. |
| 070 | Wash temperature too low. | Call us. Leave the panels on. |
| 071 | Rinse temperature too low. | Call us. Leave the panels on. |
Faults. The machine can't keep washing. The ON/OFF button stays red, and the machine switches off once you acknowledge the code.
| Code | What it means | What you can safely do |
|---|---|---|
| 001, 002 | Hot water tank (boiler) temperature sensor fault. | Call us. Leave the panels on. |
| 006, 007 | Wash tank temperature sensor fault. | Call us. Leave the panels on. |
| 011, 012 | Wash chamber temperature sensor fault. | Call us. Leave the panels on. |
| 013 | Disinfection not guaranteed. | Stop using the machine for washware that must be sanitised. Call us. |
| 014, 015 | Hot water tank (boiler) pressure sensor fault. | Call us. Leave the panels on. |
| 016 | Wash tank pressure sensor fault. | Call us. Leave the panels on. |
| 017 | Tank pressure sensor fault. | Call us. Leave the panels on. |
| 020 | Wash tank pressure sensor fault. | Pump out the machine and restart. If it comes back, call us. |
| 031, 032 | No water coming in. | Check the water supply tap to the machine is fully open. If it comes back, call us. |
| 033 | Fault in the filling system. | Call us. Leave the panels on. |
| 035 | Tank cover strainer not fitted correctly. | Refit the tank cover strainer correctly. |
| 044 | Salt low (machines with built-in water treatment). | Refill the regenerating salt as the manufacturer directs. |
| 045 | Too many cycles without regenerating salt. | Call us. |
| 049 | Handling fault. | Call us. |
| 052 | Fault in the filling or drain system. | Disconnect the machine from the water and power supply if it's safe to do so. Call us. |
Source: HOBART, PROFI AMX / AMXX / PREMAX AUP Installation and Operation Manual, DSN AMX-14-02 (document 0000000264-001-EN, May 2024), section 9.1, Fault indications.
Hobart PROFI FX (front-loading): codes that differ
The PROFI FX uses mostly the same numbers as the AMX, but some differ. Where a code isn't in this table, use the AMX table above.
| Code | What it means on a PROFI FX | What you can safely do |
|---|---|---|
| 014, 015 | Booster pressure sensor fault. | Call us. Leave the panels on. |
| 018 | Fault in the filling or drain system. | Call us. |
| 019 | Strainer blocked. | Remove, clean and refit the strainer. |
| 023 | Fault in the filling system: not enough water coming in. | Check the water tap is fully open. If it comes back, call us. |
| 029, 039 | Programme aborted (039: filling programme aborted). Close the door. | Close the door fully. |
| 042 | Reverse osmosis pre-filter used up. | The pre-filter needs replacing. Call us. |
Source: HOBART, PROFI FX Installation and Operation Instructions, DSN FX-12-01 (May 2015), section 9, Fault indications.
Hobart ECOMAX 404 and 504 (undercounter)
On an ECOMAX, the ON/OFF button lights red, Er shows on the top display and a two-digit code shows on the bottom display.
| Code | What it means | What you can safely do |
|---|---|---|
| Er 01 / Er 02 | Boiler temperature sensor reading too high or too low. | Call us. Leave the panels on. |
| Er 03 | Boiler thermostop during the wash programme. | Call us. Leave the panels on. |
| Er 05 / Er 06 | Tank temperature sensor reading too high or too low. | Call us. Leave the panels on. |
| Er 07 / Er 08 | Boiler pressure sensor reading too high or too low. | Call us. Leave the panels on. |
| Er 09 / Er 10 | Tank pressure sensor reading too high or too low. | Call us. Leave the panels on. |
| Er 12 | Water level regulation in the wash tank failed. | Call us. |
| Er 13 | Fill monitoring on the tank pressure sensor. | Drain the machine. If it comes back, call us. |
| Er 14 | Wash tank not draining in the pump-out programme. | Check the drain hose isn't kinked or blocked, then pump out again. If it comes back, call us. |
| Er 17 | Fill monitoring on the impeller (flow) sensor. | Check the water supply tap is fully open. If it comes back, call us. |
| Er 18 | Fill monitoring on the boiler water level. | Check the water supply tap is fully open. If it comes back, call us. |
| Er 28 | Wash tank level too low at programme start. | The machine refills and starts automatically. If the code keeps showing, call us. |
| Er 29 | External water treatment cartridge used up. | The water treatment cartridge needs replacing. Call us if you're not sure how. |
| Er 31 | Fill monitoring. | Check the water supply tap is fully open. If it comes back, call us. |
The ECOMAX also shows letter messages: SA Lt (regenerating salt used up, refill it), Door (a fill, wash or pump-out was interrupted, close the door) and HY (run the hygiene programme).
Source: HOBART, ECOMAX 404 / 504 Installation and Operation Manual, DSN FG-16-02 (document 0000000360-001-EN, October 2024), sections 9.1 Information and 9.2 Error.
Safe checks to try first
- Door or hood: closed fully.
- Water supply: the tap to the machine is fully open.
- Chemicals: detergent and rinse aid aren't empty.
- Strainers: removed, cleaned and refitted correctly.
- Drain hose: not kinked, crushed or blocked.
Leave the panels on. There are live electrical parts inside. If you see water near electrics or smell burning, switch off at the wall or isolator if it's safe to do so, and call us.
When to call a technician
- The safe checks above don't clear the code.
- The code is a sensor, heating, pressure or voltage fault.
- Code 013 "disinfection not guaranteed" is showing.
- There's a leak, a burning smell, or the power keeps tripping.
A Dishwasher Hygiene Check starts from $140 + GST, depending on the model. A full dishwasher service, including a hygiene check, starts from $220 + GST. Our work is covered by a 90-day parts and labour warranty.
FAQ
What does error 13 mean on a Hobart dishwasher?
It depends on the model. On a Hobart PROFI (AMX, AMXX, PREMAX AUP or FX), 013 means "disinfection not guaranteed". Stop using the machine for washware that must be sanitised and call 0800 90 60 30. On a Hobart ECOMAX 404 or 504, Er 13 is a fill-monitoring code on the tank pressure sensor. Drain the machine, and call us if it comes back.
What does error 31 mean on a Hobart?
On a PROFI, 031 or 032 means water isn't coming in. Check the water tap to the machine is fully open. On an ECOMAX, Er 31 is also a fill-monitoring code, and the same check applies. If it comes back, call us.
What do error 14 and error 17 mean on a Hobart?
On a PROFI, 014 or 015 is a hot water tank (boiler) pressure sensor fault, and 017 is a tank pressure sensor fault. Both need a technician. On an ECOMAX, Er 14 means the wash tank didn't drain in the pump-out programme, and Er 17 is a fill-monitoring code on the flow sensor. Check the drain hose or the water tap, then call us if the code returns.
Are Hobart PROFI and ECOMAX error codes the same?
No. PROFI machines show three-digit codes such as 013 or 031 with a text message. ECOMAX 404 and 504 machines show Er with a two-digit code. The same number can mean different things, so use the section that matches your machine.
Do you service Hobart dishwashers?
Yes. CES Wellington are Hobart service agents. Our factory-trained technicians (where applicable) repair and service Hobart dishwashers and glasswashers. See our Hobart page and commercial dishwasher repairs.
Error still showing?
Call 0800 90 60 30, email service@cesw.co.nz or book a job. The line is answered 24 hours, 7 days.