Merrychef error codes

What Merrychef conneX 12 and conneX 16 error codes mean, safe checks to try first, and when to call a technician.

Book a job

Error on the display and service starting soon? Call 0800 90 60 30. Calls are answered 24 hours, 7 days. Technician cover runs 7 days, with after-hours emergency cover. Our target for emergency responses is two hours. It's a target, not a guarantee, and it depends on workload at the time.

This page covers the Merrychef conneX 12 and conneX 16 high-speed ovens. On a conneX, an error shows as an E code and a short message, often "Please contact your Merrychef service partner". Before you switch off, photograph the screen and note the model and serial number from the nameplate on the back of the oven. CES Wellington are Merrychef service agents. See all brand pages on error codes.

Merrychef conneX 12 and conneX 16

CodeWhat it meansWhat you can safely do
E88 (screen shows E088)Supply voltage out of range: below 180 V or above 264 V.Call us. We'll check the site supply against what the oven measured.
E101Microwave not responding. The oven asked for microwave power but didn't get enough.Switch the oven off and call us. Leave the panels on. There are high-voltage parts inside.
E102Heater on without request. The cavity has run well above the set temperature.Switch the oven off and call us. Leave the panels on.
E103Ambient overheat. The electronics are too hot, often because the air filter is blocked.Follow the on-screen steps: remove, clean and refit the air filter below the door. Make sure the oven isn't next to a heat source. If E103 stays, call us.
E104Cavity overheat thermostat has tripped. This often happens when the oven is switched off at the wall at the end of service before it has cooled down.Call us. To stop it happening again, let the oven cool before you switch it off at the wall.
E105Mains supply frequency issue. This is common on unstable supplies such as generators.Call us. We'll check the supply and test the oven for microwave leakage.
E106Cavity overheat detected during a cook.Check for any sign of food burning in the cavity. Keep the door closed and switch off at the wall if it's safe to do so. Call us. If there's a fire you can't control, call 111.
E107Communication failure between the screen (UI) board and the IO board.Call us. Leave the panels on.
E108Screen board SD card error.Call us. Leave the panels on.
E109IO board PM chip error.Call us. Leave the panels on.
E110Firmware version conflict between the boards.Call us. The oven needs its firmware updated.
E111Cavity temperature sensor failure.Call us. Leave the panels on.
E112IO board temperature sensor failure.Call us. Leave the panels on.
E113Microwave on without request.Switch the oven off at the wall if it's safe to do so. Call us. Don't use the oven.
E116Heater not responding. The oven didn't reach 100°C within 30 minutes.Call us. Leave the panels on.
E117 / E118Right-hand (E117) or left-hand (E118) magnetron overheat, usually from poor cooling.Follow the on-screen steps: remove, clean and refit the air filter below the door, then let the oven cool. If the message stays, call us.
E-1Unknown internal error.Call us. The oven needs a firmware check.

Source: Merrychef conneX Service and Repair Manual (part number 32Z9170), section 5.2, Errors and diagnostics; and Error codes & fault finding tips.

Safe checks to try first

  • Air filter: the filter below the door is clean. Merrychef says to clean it daily. A blocked filter is a common cause of E103, E117 and E118.
  • Space around the oven: the oven isn't next to a fryer, grill or other heat source that pushes hot or greasy air into it.
  • Power: the oven is on a suitable supply, and you're not running it from a generator.
  • End of service: let the oven cool down before you switch it off at the wall.

Leave the panels on. A high-speed oven has high-voltage microwave parts inside that can hold a charge after it's switched off. If you see smoke or fire in the cavity, keep the door closed, switch off at the wall if it's safe to do so, and call us.

When to call a technician

  • The safe checks above don't clear the code.
  • The code is a microwave, heater, sensor, board or firmware fault (E101, E102, E107–E113, E116, E-1).
  • The door seal is damaged, or the oven trips the power or smells of burning.

FAQ

What does E101 mean on a Merrychef?

On a Merrychef conneX, E101 means the microwave system isn't responding. The oven asked for microwave power and didn't get enough. Switch the oven off and call 0800 90 60 30. Don't open the panels. There are high-voltage parts inside.

What does E105 mean on a Merrychef?

E105 is a mains supply frequency problem. It's most common when the supply is unstable, for example from a generator. Call us so we can check the supply and test the oven.

What does E88 mean on a Merrychef conneX?

E88 (shown on the screen as E088) means the supply voltage is out of range, below 180 V or above 264 V. Call us. We'll compare the oven's reading with the site supply.

What does E111 or E116 mean on a Merrychef?

E111 means the cavity temperature sensor has failed. E116 means the heater didn't get the oven to 100°C within 30 minutes. Both need a technician. Call us and leave the panels on.

How do I stop E103 and E117 coming back?

Clean the air filter below the door every day, and keep the oven away from heat sources. Both codes are usually caused by poor cooling.

Are you Merrychef service agents?

Yes. CES Wellington are service agents for Merrychef and TurboChef high-speed ovens. Our factory-trained technicians (where applicable) work on the conneX range. See Merrychef conneX service and repair and Merrychef and TurboChef oven repairs.

Error still showing?

📞 0800 90 60 30

Call 0800 90 60 30, email service@cesw.co.nz or book a job. The line is answered 24 hours, 7 days. Our work is covered by a 90-day parts and labour warranty.